 |
| Quantity: | |
|---|---|
KYDBL4815-1E
Keya
KYDBL4815-1E
24v 200w RS232 communicate bldc controller
KYDBL4830-1E is an intelligent brushless DC controller. Support RS232, CAN open communicate, suppot jostick, RC, PWM, 0-5V control, encoder feedback for close loop control motor speed or position.
II.Product parameter
| Controller type | Single channel brushless dc controller |
| Voltage Range | DC10-55V |
| Continuous current | 8A |
| Max current | 15A |
| Work mode | Speed open-loop, close-loop control, torque close-loop control, position close-loop control |
| Operation mode | Safety forward & reverse control, four-quadrant operation, support regeneration. |
| Feedback | Hall sensor, 500ppr - 2500ppr Incremental encoder |
| Control ways | RS232, CAN-Open, PWM, Analog voltage(0-5V or 0-2.5V-5V), RC Radio, Jostick |
| Protection | overcurrent, overheating, overvoltage and short circuit will start the protection function. |
| Working temperature | -10℃-- +60℃. |
| Boundary dimension | 90mm * 75mm * 35mm |
| Weight | 185g |
| Applied range | This bldc controller be widely used in medical robot, automatic guided vehicle, self guided vehicle, rail guided vehicle, unmanned ground vehicle, robot arm, intelligent warehouse, intelligent system etc |
Control port
Standard DR25 inerface, the port detail definition as below:
| Interface | Definition | Function | I/O |
| 1 | Fault alarm output | Can be set | DOUT2 |
| 2 | Tx-out | RS232Tx | |
| 3 | Rx-in | RS232Rx | |
| 4 | Enable control EN | Effective for high level | DIN5 |
| 5 | GND | ||
| 6 | Reversing control DIR | Effective for high level | P/AIN4 |
| 7 | Controller output | 5V (20mA) | |
| 8 | Controller output | 5V (20mA) | |
| 9 | CANH | CAN-high (Support Can open) | |
| 10 | CANL | CAN-lower (Support Can open) | |
| 11 | GND | ||
| 12 | Input signal IN | DIN3 | |
| 13 | Controller output | DC 5V（20mA） | As potentiometer supply |
| 14 | Fault alarm output | Can be set | DOUT1 |
| 15 | BLDC motor hall power + | ||
| 16 | BLDC Motor Hall---A | ||
| 17 | BLDC Motor Hall---B | ||
| 18 | BLDC Motor Hall---C | ||
| 19 | BLDC Motor hall Power- | ||
| 20 | Encoder feedback power + | ||
| 21 | Encoder feedback input---B+ | ||
| 22 | Encoder feedback input---A+ | ||
| 23 | Encoder feedback power | ||
| 24 | Brake STOP | Effective for high level | DIN6 |
| 25 | Controller output | DC 5V (20mA) |
If you need more information, please leave message, we will try our best to support you on this bldc driver.
24v 200w RS232 communicate bldc controller
KYDBL4830-1E is an intelligent brushless DC controller. Support RS232, CAN open communicate, suppot jostick, RC, PWM, 0-5V control, encoder feedback for close loop control motor speed or position.
II.Product parameter
| Controller type | Single channel brushless dc controller |
| Voltage Range | DC10-55V |
| Continuous current | 8A |
| Max current | 15A |
| Work mode | Speed open-loop, close-loop control, torque close-loop control, position close-loop control |
| Operation mode | Safety forward & reverse control, four-quadrant operation, support regeneration. |
| Feedback | Hall sensor, 500ppr - 2500ppr Incremental encoder |
| Control ways | RS232, CAN-Open, PWM, Analog voltage(0-5V or 0-2.5V-5V), RC Radio, Jostick |
| Protection | overcurrent, overheating, overvoltage and short circuit will start the protection function. |
| Working temperature | -10℃-- +60℃. |
| Boundary dimension | 90mm * 75mm * 35mm |
| Weight | 185g |
| Applied range | This bldc controller be widely used in medical robot, automatic guided vehicle, self guided vehicle, rail guided vehicle, unmanned ground vehicle, robot arm, intelligent warehouse, intelligent system etc |
Control port
Standard DR25 inerface, the port detail definition as below:
| Interface | Definition | Function | I/O |
| 1 | Fault alarm output | Can be set | DOUT2 |
| 2 | Tx-out | RS232Tx | |
| 3 | Rx-in | RS232Rx | |
| 4 | Enable control EN | Effective for high level | DIN5 |
| 5 | GND | ||
| 6 | Reversing control DIR | Effective for high level | P/AIN4 |
| 7 | Controller output | 5V (20mA) | |
| 8 | Controller output | 5V (20mA) | |
| 9 | CANH | CAN-high (Support Can open) | |
| 10 | CANL | CAN-lower (Support Can open) | |
| 11 | GND | ||
| 12 | Input signal IN | DIN3 | |
| 13 | Controller output | DC 5V（20mA） | As potentiometer supply |
| 14 | Fault alarm output | Can be set | DOUT1 |
| 15 | BLDC motor hall power + | ||
| 16 | BLDC Motor Hall---A | ||
| 17 | BLDC Motor Hall---B | ||
| 18 | BLDC Motor Hall---C | ||
| 19 | BLDC Motor hall Power- | ||
| 20 | Encoder feedback power + | ||
| 21 | Encoder feedback input---B+ | ||
| 22 | Encoder feedback input---A+ | ||
| 23 | Encoder feedback power | ||
| 24 | Brake STOP | Effective for high level | DIN6 |
| 25 | Controller output | DC 5V (20mA) |
If you need more information, please leave message, we will try our best to support you on this bldc driver.
